Firestone W217602250 Ride-Rite Kit for GM C2500HD/C3500
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Mine was for a Chevy 2007 Classic 2500 HD, but I don't know the make/model.
It is a bit confusing. I know I like air bags, but I agree with the comment above that
There are two of these that I think In the "Vehicle Service Type" they are a fit for a 2001 GMC Sierra 2500HD and the Chevy is very similar.
On a 2wd GMC 3500, it had a rear sway bar that made it difficult to install (I had to tack weld one of the u bolts because it was impossible to tighten it with any type of tool) but it worked. In addition to installing one on my Toyota 4x4 without the rear sway bar, I also put one on an 02 Chevy 3500 4WD. It may be helpful to you.
Selected User Reviews For Firestone W217602250 Ride-Rite Kit for GM C2500HD/C3500
My 2007 Silverado 2500 HD Truck Camper has been happy with this. It is not advisable to use a tee that fills both at the same time. When you turn a corner, the air is pushed to the other side. This makes for less accurate handling. My attempt at both methods was unsuccessful.
My 09 GMC 2500HD came with these after I installed them to ensure that I could tow a 29' fifth We are very pleased with the improvement over bounce and harshness of bumps as well as the leveling of the truck. The T and the single air valve were also installed to make sure they always have the same It took me about five hours to install the software. It took me about an hour to read and watch the instructions to ensure everything was lined up perfectly. I also like to take my time so I really did make sure everything was in place before finishing installation. Check to make sure the exhaust heat shield is aligned exactly right before you finish the job!.
The Chevrolet 2500HD Duramax is a 2005 model. It takes 3 hours to complete the installation. I had to remove the drivers bag because the frame's welds were in the way of the entire top plate. There is a ground collapse. I reinstalled it. I love it!.
It's the third time I've put them on the truck. The whole thing is The only thing missing is a white shirt. My favorite ride rite bags are the messenger The set was installed on a 2007 Chevrolet. The 2500HD (LMM) format is five. Moreover, on the left side, the lower bracket can rub the cable of the parking brake and, more important, the hydraulic tube of the rear brake. If you remain cautious during installation and reinstall those clamps every few days to keep a gap, you will be fine. You need to remove the spare tire to assist installation, and you need to learn how to remove it if you haven't done it before. I've never seen anything as dumb as this. It would be nice if Toyota just made a diesel tundra instead of fooling around. One and a half tons. The dream is just a wish. Yes, I do.
Based on the recommendation of my friend with whom I bought my 36' gooseneck trailer, I purchased these as well. These airbags will make towing much easier, he said. Then I installed them immediately before I bought his trailer, and I felt as though I had nothing behind me when I was driving. The trailer air bags were run around 60 psi, while the car air bags were run around 5 psi A 10psi pressure is required The pin weight of 2000 pounds does not sag the truck at all in the back. I have found that these air bags are amazing, and I really feel as if my 2007 Chevrolet Silverado HD Duramax rides like a new truck now.
A 2007 Mercury Silverado 3500 Classic extended cab, LBZ, recently had a new grille installed. After watching a couple YouTube videos I downloaded and installed the app. We worked on it for a couple of hours and could not be more pleased. I am impressed with the quality and the packaging of the parts. It's been a couple of years since we used Timbrens to tow a 37-foot fifth wheel. Despite mounting the Timbrens a full inch above the axle, the rear of the truck still sagged a little. Having the air bags adjustable and being able to level the truck are handy features. A truck that is not carrying a load rides much more smoothly. Rear end does not have the same harshness as the front. As long as I am not carrying a load, I keep the bags inflated at 10psi. Excellent product. I highly recommend it.
I estimate it took an hour total to complete the By the trailer harness, I mounted the inflation valves in the rear bumper. On the axle and frame, so it bolts right on. Bags from this brand are much better quality than bags from the AirLift brand. Everything I need to do now is get the wireless connected I'm on the board Make sure to demand a compressor, and everything will be fine!.
This has been terrific. It can be installed with a standard socket and wrench using a bolt-on system. We spent about two hours together, with the help of my wife. Our choice wasn't to purchase the kit that includes the air compressor and switches, but rather to purchase a $20 Harbor Freight air compressor. Ten seconds is the time it takes to go from empty to full pressure.