Design Engineering 050310 Boom Mat Speaker Baffles, 4" Round (Pack of 2)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I suggest investing in some speakers.
I do believe that the bass is more solid and better, and that the "boxy" sound produced by the door enclosure has been eliminated. It, in my opinion, removes unwanted resonances that distort the sound's clarity. If I had the option, I would reinstall them. One word of caution: they come in a variety of sizes, so you may have to cut them to fit your door cavity. When I cut the first baffle, it was a little loose, which caused an unwanted vibration between the cavity's plastic and the foam baffle, which were both barely touching. To fix this, I cut the next baffles to fit tighter in the cavity and eliminate the vibration noise.
Check the clearance carefully in some vehicles where the speakers are mounted on a middle steel panel and the whole shebang is then pressed against a speaker grill molded into the inner upholstered door panel, as it varies a lot and this little thing can add up to make a firm panel fitment at that corner a bit difficult. The plastic grille area can be trimmed at any time. This is a rare occurrence, but it has the potential to be significant.
I've noticed that lower frequencies are less pronounced, which is fine by me. I've turned it off because I'm using it to combat the damaging effects of water leakage caused by a faulty window seal. If you mean a designated enclosure when you say 'can,' then yes. If anything, I'd skip this step and instead use polyfill. The reverb from highs and mids bouncing off metal should cancel out in a bare door cavity. Individual cans are what these are essentially.
Selected User Reviews For Design Engineering 050310 Boom Mat Speaker Baffles, 4" Round (Pack of 2)
in a negative way! This product is not being mocked in any way. Maybe it works for you, but let me tell you about my personal experience. These were used in conjunction with my new speakers (Infinities 6). In my 2008 GMC Sierra pickup truck, I have a 75" screen with a factory stereo. There is a known issue with the truck speakers failing, with rumors that it was due to a water issue in the door, but I found no evidence of this. Anyway, I put these boom mat speaker baffles in because they were supposed to improve sound and keep moisture out. When I turned on the radio, there was no bass at all. Only high mids and highs were available to me. It sounded mono stereo to me. I assumed it was a speaker issue because a Crutchfield rep told me that the infinities I installed should perform as well as my factory speakers. So I ripped the boom mats off and "WOW" what a difference in sound there was. Finally, my lows and mids sounded normal, and my bass was excellent. The bass was drowned out by these boom mats, and the sound was completely altered. I'm not sure why these are required. I strongly advise you to avoid it. for a minimum of 6 Speakers that are 75" tall.
br>br>I have a S2000 and purchased these to protect my door speakers from water damage and to improve overall sound, but all I got was a little bit of protection and minimal sound improvements in the end. br>br>I began by installing the baffle on the right side, and immediately noticed that the mids and highs were improved, but the bass sounded muffled and odd when compared to the left side, which had no baffles. br>br>(I did this by switching from the right to left speaker on the car stereo)br>br>I then cut a 2" hole in the back of it and tested it again. The bass was better this time, but still not as good as it had been when I listened to the left speaker without a baffle. br>br>I ended up chopping off the bottom half of the back of the baffle, which improved the sound and provided some protection against water entering the door. br>br>I hope this information is useful to others.
I paired them with some Rockford Fosgate speakers that I've previously used in other vehicles and enjoy for their crisp highs and deep bass. I'd never used baffles before, so I decided to give it a try. br>br>After I installed them, the speakers were not only quiet, but also lacked any bass. As a result, I drilled a hole in the baffle's side. This immediately resolved the problem, and the speakers now produce tight, low bass. br>br>I'm guessing that because the speakers were mounted directly to the baffle surface, they created an air-tight seal. The baffle's high density foam creates a tight seal. As a result, when the diaphram tried to move, it was battling the neutral volume of air trapped behind the speaker. The trapped air would pull the diaphram back to neutral when it wanted to move outward. Similarly, if the diaphram attempted to move inward, it would be pushing against that static volume of air, increasing air pressure. The speaker's efficiency was reduced as a result of this. Just to get them moving enough to hear if they were giving me full range or if I had messed up the polarity or something, I had to turn up the stereo almost all the way. br>br>To relieve the pressure, I cut a one-inch square. The foam is still in place now, so it can handle reflections and improve the acoustic properties. However, by allowing air to flow freely behind the speaker, the efficiency increased, and I no longer need to push the speakers as hard, and they sound great even at low volumes. It's a fascinating concept. br>br> Each door is equipped with baffles. I get it. However, acoustic setups (in which the box is sealed behind the woofer) are rarely used in subwoofer box design. Instead, there is always a port where air can enter and exit. Perhaps using a riser or adapter between the baffle and the speaker would provide enough air movement to avoid the need for a hole in the baffle. However, in order to save space, I mounted the speakers directly to the baffle.
This is made of flexible foam, similar to the foam used to keep the heat in around hot water pipes, but thinner. Because they're quite thick, you'll want to make sure you have enough room for your speaker to be a full 14" higher than it is now. There is no air movement, they're not a sealed enclosure made for your specific speaker, and the majority of 6x9's are "infinite baffle" speakers, which means they're designed with nothing behind them. I made a 1" x 1" x 1" x 1" x 1" The addition of a 12" hole on the downward side resulted in a significant increase in sound output and bass production. But it also gave me more control, as the speakers didn't distort as much at the previous volumes, and I was able to get 4-stars. As a result, there are 5 additional volume increments. That was fantastic!.
Boom Mat Speaker Baffles, DEI 050330, 6, 5" Round. " So, as someone who orders and talks about speakers in terms of their size - You'd think that getting a 6 would be a good idea. A 6 would fit in a 5" ROUND baffle. Speaker size is 5 inches. No so. This thing is six feet tall. 5" square (measured from one side to the other). It's barely big enough for a three. Speaker is 5" in diameter. Completely deceptive, and their expanded model details do nothing to help clarify what to buy. I'm not going to order any more of these, and I tossed them out.
Related Products For Design Engineering 050310 Boom Mat Speaker Baffles, 4" Round (Pack of 2)
