Set de forros U POL Raptor, rociados con uretano negro, para plataformas de camiones con pistola rociadora gratis, 4 litros.

In addition to the many other comments, I am quite satisfied with this product. Before I began using it, I had two major concerns How much product would be needed to adequately cover my truck bed, and would it look good when it is completed? A resounding yes was given to both questions. As for the coverage, let me start with that. In this case, I applied the product to a short bed Chevy Silverado, but did not do the tailgate since it had a plastic cover that was in good shape, so I expected that the four 750 ml bottles would be sufficient. For my application I only needed about 3 bottles for the two good coats I applied, so I could have applied even heavier coats for the short bed. With regard to the appearance of the product, I applied it using the spray gun that was furnished. A great job was done by the program. The paint applied evenly without any uneven sections (no thin or thick patches), and I was very pleased with the end result - textured, yet practical. They were certainly comparable to the professionally applied bed liners I had acquired for my previous pickups. To learn more about their application, I've taken a few tips from those who have gone before me (thank you!). For several days before I sprayed, I choreographed my moves (mentally and physically) so I could get a feel for how I wanted the coating to be applied. It is important to understand how to hold your spray gun and air hose to prevent tangles and obstructions, how to spray in corners, seams, and over tire wells in order to get a good amount of coverage, but not to overdo it. Then it was a matter of finding out how to apply in those tricky areas, and 3) how I wanted to spray the horizontal surfaces before shifting my attention to the verticals as the bottles became more and more empty. The information I gained from this helped me tremendously when I started spraying (I am not an expert at this). My practice also revealed that the air pressure of my pancake compressor shifts by about 15 psi from the beginning until finishing of a spray pass (without the use of a bottle). To produce a steady 55 PSI I found that if I set the compressor regulator at approximately 70 PSI, then added an internal regulator I was able to accomplish this I had a line regulator attached to my line Once it was set to 55 PSI, it would hold that pressure at a maximum of 55 PSI plus a little bit It has a PSI of 3. It made me feel like my application was much more consistent. So for my final thoughts, I am extremely pleased with this product. The prep is a bit time-consuming, but the results are outstanding!.

Everleigh KAUR

| Apr 10, 2021

This is the DIY bed liner that I narrowed down after doing lots of research. In the end, I went ahead and bought it after watching lots of videos and reviews. Ford F150 6 2012 In two bottles I was able to get 5 bed coated. For the two other bottles, I turned up the PSI and shot them at an angle of about two feet away to give it a dull, rough appearance. The product is great!! I highly recommend it!.

Genesis Vazquez

| Sep 24, 2020

Simple to use if you have some experience with painting and spray guns. If you don't proceed with some care and carefully follow the instructions. Making sure you prepare is Firstly, I pressure washed the truck bed and sanded and scuffed all parts of the bed (to avoid any A #8 primer was applied to any bare metal. Then I blasted the bed with air, wiped everything down with lacquer thinner, then mask everything off. When I mixed each liter at a time, I sprayed it at 60 pounds per square inch with the supplied gun and 8-foot hose As much as possible, use a compression sprayer to spray at least 18 inches away from the surface at a 90-degree angle. The amount of liquid that was consumed was In keeping with saving for one more small project and for the tailgate (which I took off), I will spend the 4th on those two things. There are several considerations to take into account A mask or respirator should always be worn as a first precaution There should be no open flames Be sure you have a hat and long sleeves on. Do not sweat if it is hot. You should wipe it dry before you begin. While you are working in tight places, make sure the bottom of the can or hose does not drag in the wet work. It is generally a very forgiving material with minor imperfections. So there's no need to drop cloth the entire garage since there wasn't a lot of overspray. Ultimately, I am pleased with the outcome and will update later on how it stands.

Harlem Oliver

| Nov 18, 2020

The result worked perfectly. I was able to perform and put on the dress without issue after everything had been prepped. With a thick layer of three bottles, the short bed truck bed was covered. In addition to the tailgate, you can easily cover the bumpers and wheel wells with the fourth bottle. Observe these tips I. 1. We recommend you wear the best quality organic vapor respirator you can find. There is nothing toxic about this The truck had a big fan blowing across it, and I was outside wearing my respirator, and I could still catch a whiff of it. Make sure you have plenty of nitrile gloves on hand. It is likely to splatter a little due to overspray. Please see (2). Apply ACETONE to the sprayer to clean it. Neither the directions nor the cleaner mentioned in them say what to use It is just to keep the bottles clean between each other. If you want to clean the bottle, unscrew it and put 1/4 cup an acetone in a yogurt container or jar. The intake straw should be dipped in the acetone and squirted into the cardboard box by pressing the trigger. This product is instantaneous. Remove the nozzle from the container and wipe it clean 1. 2. 3. The next bottle can be mixed by your helper so that you do not have to clean the nozzle, but even if you wait a minute before spraying it, the nozzle will become Additionally, your helper can combine the product left in bottom of the bottle with the mostly empty bottles and you can easily get a second cup of product. Pour a tiny amount of reducer (not acetone) into the cup and get the most for your money. 4 * . You should spray the product by holding it steady while shaking it - there is a breather hole in the top of the sprayer. When the glob spills, it will stick to the ceiling. The horizontal sprays should be done first when the bottle is about 1/4 full. Save the vertical sprays for when the bottle is 2/3

At the end of the day, if you tape and mask properly, you can get an amazing result.

Nathalie Roberts

| Dec 21, 2020