2pc 6" White Oval LED Reverse Trailer Tail Light Kit [DOT FMVSS 108] [SAE (2) R] [24 LED] [Grommet & Plug Included] [IP67 Waterproof] [Back Up Signal] Trailer Lights for Boat Trailer RV Trucks
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The dimensions are 5 inches by 2 inches. In order to use this size hole, it needs to be 5in.
That doesn't seem to be the case. Based on the specs, I would guess that it is rated at 10-14
Thanks in advance. I hope this helps. The grommet extends approximately 3/8" and the boarder is about 1/2" wide.
In my case, the red is quite vibrant on the back of the
Selected User Reviews For 2pc 6" White Oval LED Reverse Trailer Tail Light Kit [DOT FMVSS 108] [SAE (2) R] [24 LED] [Grommet & Plug Included] [IP67 Waterproof] [Back Up Signal] Trailer Lights for Boat Trailer RV Trucks
It does not seem to be a bright person. As you can see, the rear lights are on in the photos but they aren't visible in the daytime. Even during the day, the stop lights are barely noticeable. A video showed people installing a set of them and they didn't have any trouble doing it. In contrast, I was worried I would break the light or the mount when I was handling these.
In an enclosed box truck for extra light inside, I have installed these LED lights. They have worked well. During the first 6 months, I bought some Partsam lights and half the LEDs stopped working. Other LEDs began flashing on and off intermittently. I am far more satisfied with these lights than I was with the Partsams that I had If I have any issues with these in 6 months, I will update my review.
Light bulb is not quite the same size as the incandescent light bulb One of the lights on my trailer went out and I replaced it with an LED unit. The sun was clearly visible when I left my house, but by the time I arrived at my destination, it had disappeared! The package came with two, which was a good thing. As far as the second one goes, I installed it with silicone adhesive. As compared to the original, the new light is slightly smaller in both directions.
These are the perfect fit for the holes on my construction trailer that I use a United Trailer for. Having finished the wiring (Emco 7-46, This is the wire harness for the center wire in the following However, the LEDs do not cast a blinding light on those operating a vehicle in my driveway behind me. Instead, they brighten up the entire yard In an earlier draft, I was going to use a non-white paper It would have been nice to use the DOT set of utility LED pods, but I wanted to adhere to the law (using DOT approved lights) and use lights that matched the trailer's current These are great and I'm glad I got them.
These power supplies run on 2V and LEDs are included in greater numbers than other offerings at this price point. The tail lights are superior to standard bulb tail lights in terms of brightness and efficiency. These are sure to catch the attention of the drivers behind you! There is a connector harness included that has a snug fit for the lights. It is a standard contact pattern, so you can use the old harness connector if you prefer, so that you don't have to splice the.
A respondent replied that regardless of the measurements, they were still the same size. Close but not exactly precise. The screw heads don't fit as perfectly as the originals, but they look like they will work just fine. It has only been a minute since I took the trailer out, but so far the lights have stayed in and there is no flickering. I have not had the chance to take my wife out yet so she can give an accurate reading of the light's.
The “equivalent” lights are not as good. The quality product is worth the extra money. A solid construction and a pliable seal allow this kit to seal well to the vehicle. It is important to note that these lights are not surface mounted There are two types of mounting holes - oval and round - that the lights should mount It includes a cutting template, but there is also In most cases, it is highly desirable or necessary for the vehicle surface to be cut with a 5X hole saw.