HYCLAT Red 50A 6-10 Gauge Battery Cable Quick Connect Disconnect Electrical Motors Plug Wire Harness Plug Connector Recovery Winch Trailer (4 Pack)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
In my experience, I have successfully connected power to a winch with a pair. The issue is that I cannot tell you if they would fit with any other specific brands of connectors.
That's correct, it is perfectly suited to 8 ga.
The only thing they plug into is each other. Aside from that
It will not fit in the "6-inch" barrel, thus you cannot use it As I discovered, there is a "10ga" connector
Selected User Reviews For HYCLAT Red 50A 6-10 Gauge Battery Cable Quick Connect Disconnect Electrical Motors Plug Wire Harness Plug Connector Recovery Winch Trailer (4 Pack)
The wires are slid into the red connectors once the soldered connectors are attached to the wires. After that, I replaced the wires to the tractor, one connected to the battery and one to the tractor. The red connectors broke when I connected them together. The police did not use excessive force in any way. I would have put on some epoxy and used it if they had cracked, but they split into many pieces instead. The plastic appeared not to have been fully melted, from my observation. The task was simple it was just too bad the plastic red connectors were so bad.
To use on those occasions when reversing winching is a necessity, I bought a winch to mount to my receiver. Added new quick connectors on the winch cable and crimped the pins on the cable instead of soldering them. I trimmed the wires as needed on the cable and installed the new plugs. My rear winch now works perfectly and I have a portable winch I can use when needed. Connecting to the network is quick. If you want to solder the wires into the pins, here are some tips. Make sure there is no excess solder on the outer part of the pin (like I did). There will not be enough depth for the pin to go into the plug to lock it in place. There is no way to go wrong for $12.
In order to work with wires of heavier gauge, these connectors have excellent handling characteristics. In order to install the metal connectors into the plastic housing, they must first be soldered on to the wire. connectors are held firmly in place by the housing, and the connection between the connectors is of very high quality. When short wires (positive and negative) are installed within one plastic housing to the battery, it makes it easy to connect an extension to it through Plugs are supplied with each connector in order to prevent dirt and grime from getting into the internals. Secure connections that are cheap, simple, and easy to use.
They are a nice tight coupling that is easy to connect and disconnect. The plastic is thick like Lego blocks so I won't have to worry about stepping on it accidentally shattering. A very easy assembly is required. The #8 AWG wires were crimped and soldered together. A huge advantage of dust caps with wire cable retainers is that they can hold the cable in place.
ASSURE THAT YOU FIND A SECOND It was unfortunate that I only needed eight points Ten gauge is available, AWG, and there are a few other sizes as well. However, the instructions are terrible. There is no phone number or name on the instructions, so it is very hard to reach customer service. The illustration in the instructions is very unclear. It took some time and effort to disassemble and put back together Put the pieces back together. When I tried to assemble it for the first time, the contacts did not match, so I had to take it apart and reassemble it. The hint is It is important to make sure that the little step at the end of the terminal pin is facing down (not up), so that the contacts can connect. I hate that.
Very good connectors with a good price. In order to perform road service, a set of jumper cables with an extension of 25 feet is needed. With a propane torch, I was able to solder / install this connector on battery cables in a very short amount of time. Usually, one end of my truck battery is permanently attached to my jumper cables as well as the ends of my The jumper cable can be extended easily from 12 feet up to 35 feet when necessary.
As it turns out, these surpassed my expectations. It was quick and easy to install, and I could not be happier with the quality. It is recommended that you use a propane or butane torch to heat the lugs and pour in half a cup of solder, after which you insert the stripped wire into the This method works much better and it is much faster than using a soldering iron to heat up such a large surface. As soon as the need arises in the future, I'll buy more of these.
The trolling motor I use has a quick disconnect, so I decided to get one. These were the ones I found and they worked They were installed two days ago, so I don't know how well the connectors will hold up, but the mating force appears to be good (once I realized that I had to firmly seat the contacts within.