MORryde RPB72-7910-05 Pin Box System, 14-18K GVWR - Leland 7910
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It was quite easy to install Due to my inexperience, I spent the most time following the hole alignment of the rear bolt holes. There are no holes to be found. Bolts, lock washers, and nuts had to be replaced as they were grade three (I purchased grade 8) Original installation had 8 bolts and the MorRyde lined up (without having to drill) with 10 holes - I replaced all three at the same time. It was a good opportunity for me, and I'm feeling much better for it. As it is still a little chilly here, I have not yet had the chance to take the MorRyde out to see how much better it performs. Thanks for your interest - best of luck In order to make the purchase of the MorRyde, I did a considerable amount of research.
When loaded, your trailer can be 14k lbs, but you will likely have 1500 lbs to 2000 lbs of cargo on top of that, so you are probably closer to 15,500 to 16,000 lbs. There's no point in having too much capacity if there isn't
About 50 lbs are contained in the hitch and the bolts weigh 12 lbs each.
In order to adjust the camper's height, just move the pin box up or down in the holes in the pin box. You should have enough pins in the mount for your camper to use if there are more holes than the pin box in your existing box.
Selected User Reviews For MORryde RPB72-7910-05 Pin Box System, 14-18K GVWR - Leland 7910
There has been such a dramatic improvement in ride quality! A new ID is a must! Don't let yours go to waste! It is easy to install (make sure you order the correct one), just watch the youtube video and you will be able to hook it up! The box it comes in will be destroyed but the hitch inside is perfect, and it is really heavy. . . so have help with it.
The bumps and the jolting caused by pulling my RV are too much for my Pacemaker. My life would be a lot easier with this Pin Box. The MORryde Pin Box would have forced me to stop camping if it wasn't for it. Previously a tow was jerky. Now it is smooth! It is a must for those who use Pacemakers. Thanks for your kind words!.
Our fifth wheel is 40 feet long, so we purchased this pin box for it. We were getting a pretty aggressive chuck every time we went over an obstacle on the interstate with the factory box. successfully installed the MORryde and left the next day for a 2300 mile round trip to Florida, and we were thrilled with the results! There was an 80 percent reduction in chucking due to this. You never felt a chuck when there was one, but when you did it was very smooth and supple! I am very pleased with this product! I would recommend this product to anyone. The installation process is straightforward.
It is possible to choose from a wide variety of pin boxes, most of which are great for a variety of It is one of the best pin boxes I have ever seen. This system is smooth when you take off from a stop. There are a few bumps, but it makes the ride seem so smooth that you almost forget you have a 16000 pound, 42 foot fifth wheel behind you!.
It came earlier than I expected the packaging on the hitch was very good, but the box in which the hitch came was pretty beat up. The mounting ears on one were a little bent once they were bolted into place, but they straightened out after that. With a compact tractor and loader, the system was relatively simple to install.
Since I have only made one 1200 mile trip I can tell the difference between MORryde and other enhanced pin boxes. I chose the MORryde over other enhanced pin boxes due to its positive reviews, low weight, and best price. You'll hear less chucking and most of the bounces and jars of the road will be absorbed.
Make sure there are no damages in your shipment. As described in the advertisement, the Rubber Pin Box fulfills its purpose The result is a greater reduction in back pain The next time you tow your fifth wheel trailer, try "chucking" back and forth. While it does not completely eliminate chucking, the motions are smoother and smaller, which is a major improvement over in-wheel chucking. This is an easy to install kit with a helper and appropriate You will need two 15/16" sockets, plus a socket wrench and torque wrench (both required), as well as two 15/16" sockets As I had only one socket the right size, we had to use a crescent wrench and torque wrench to do the work. Follow the detailed instructions that come with the item.
One thing to keep in mind The pinbox is shipped from MORryde in a box that is too large for it to fit, and the top of the box is not blocked, so it could move around Heavy pinboxes can push right through the cardboard, and the few pieces of padding that are there do not adequately protect them. Clearly, this packaging has been designed for use at a point-of-sale Shipping by truck to a specific point does not require the UPS system nor single driver delivery. Thus, the first pin box I received had a kingpin poking through the outer box, which was pretty battered. The pin box we were going to install had been damaged during shipping, which resulted in one of the mounting flanges bending and breaking, rendering I received a new one from Amazon and Amazon picked up my old one for return, which was no big deal except for some time and As for the second one, it arrived damaged in the same way and with damage to the box, but the pinbox itself did not show any damage. I would recommend that, if you order this item, to inspect it carefully upon arrival and before you remove your existing pinbox (not after!.
Using this MOR Ryde, I was able to tow my 42' fifth wheel in comfort. A friend of mine drives a 2017 GMC 2500 diesel and the herky jerky is The tow gets a lot easier with it. This is a highly recommended book!.