Haus Maus - The Original Laundry Guard - Keeps Laundry from Falling Behind Most Front Loading Washers/Dryers - Magnetic - 50.5" x 21" x 8" - Made in North America

It works well overall, but I had to make a couple of modifications. This is because the top of my laundry machines has kind of a catch-all design and I often end up pushing things off the back of them. As a result, that did not happen to an extent. These pieces are only magnetic at the sides. Things were allowed to slip through the back as a result of being pushed over the edge. A rubber strip I had from another project was added to prevent it from sliding, and so far it seems to be holding up well. Fixing this issue is easy, but I dislike having to re-check things I assumed would work by themselves. The concept was great, but it would need some testing in a real-life laundry room to make sure it works.

Willow Mullins

| May 15, 2021

There was a set of these that I got and didn't use much of. You could wire three panels together and attach them to a washer or dryer. The panels might fit well and work well. The backside, however, is too short if you try to span both appliances and connect all four panels because the backside must span the gap between the machines so they will not rub against each other as they spin. are not very strong, and they are only on the side panels, so if you are spanning the two machines, the back panels have no anchors or anchor points, so it is easy for the things behind the machines to detach them from their edging.

Pearl Sampson

| Apr 10, 2021

As a result, I did not need the extenders, and each guard fitted my machines perfectly without them. The money has been well spent since I don't have to fish anything from behind the machines, which has saved me so much in back pain! The place where you want them is easy to adjust however, if you fill up your washer with too many things, it may end up moving back because it's.

Alfredo Colling

| Mar 20, 2021

The mention of rare earth magnets actually gave me the impression that it would be very difficult to move or adjust the rails once they were Although it appears to have a strong magnetic hold, the hold is not as strong as it appears. By gently pushing with my finger, I am able to move them easily. In the midst of a spin cycle, I feel the washer shaking, and this unit will not coral anything left on top of the washer when it does so. It would not be a purchase I would make.

Kashton Turner

| Dec 01, 2020

I had the unfortunate task of removing the old washer/dryer unit once I got a new one and cleaned up around it once it was How great it is to find treasures like this. You may have lost earrings, socks, belts, etc. When I began searching for a solution on Amazon, I found what I needed. I found them to be very easy to install when they arrived. I am confident that the magnets along the bottom will be strong enough to hold a mound of dirty standby It seems like a sturdy plastic! I can't attest to its durability, but to me it looks like a sturdy plastic!.

Ricky Barber

| Jun 20, 2021

I found this item to be brilliant when I saw it. I do use the top of my washer and dryer, but I feel like the cat likes to climb up and push things over the back. One of the appliances has a cat bed on it, so this seemed to be a good option. It has worked well in the past, but it does have one big drawback. It does look and fit as described, and it will help, but it does not have enough magnets to hold to the appliances securely enough to work. Objects will not slide off the back of the appliances, but anything weighing more than 15 pounds will rip pieces out I gave it a three star rating because of this reason. This magnet is adequate for covering one appliance if you are using it, but I bought two to cover two appliances, and it isn't enough to do the job. Then you really need two units if you decide to buy this for both appliances. I probably will buy another one because of this, so I am not disappointed with my purchase, while I had hoped one would be sufficient.

Lilith Maloney

| Apr 15, 2021

However, there are a couple of things to keep in mind There are two issues with front loaders since 1) they do not fit snug against one another and 2) a lot of front loader washers move, bobble, etc. This causes the guards to move on top of washers and dryers, which makes them look For this solution, you will have to buy two guards and eliminate a back piece so that you are left with a smaller 3 part guard that fits those components individually. This is not the most cost-effective approach, but it works just fine. It is a pleasure to have my two guards on my own. I just wanted to update you on something- In response to my review, the seller contacted me and said she was working on an extension to make the back wider, resulting in my rating going down from 3 stars to 4 since she has been proactive with addressing any issues that may arise.

Kathryn Hogan

| Jun 01, 2021

Using this method, I don't have to stress out about it, and it's an easy way to prevent me from asking my husband to move the washer dryer once a week so that I can get the items that.

Taylor HEWITT

| Dec 13, 2020